挂机清洗流程：

Hanging machine cleaning process:

1、试机：接通电源，开启空调，测试空调出风、制冷、屏显等功能是否正常；

1, test machine: connect the power supply, open the air conditioning, test the air conditioning air, refrigeration, screen display and other functions are normal;

2、用户在派工单签字确认；

2, the user is sent to confirm the signing of the work list.

3、空调下方位置铺设一张一次性塑料薄膜。

3. A disposable plastic film is laid in the position below the air conditioner.

4、拔掉电源，依照顺序卸掉空调导风片、过滤网放置一旁等待清洗；

4, unplug the power supply, discharge air conditioning air guide in order, filter the net and wait for cleaning.

5、套上空调专用清洗防水罩，将清洗防水罩下软管接入下方污水桶中。

5. The special cleaning and waterproof cover of the air conditioner is put on the air conditioner, and the hose under the cleaning waterproof cover is connected to the bottom water bucket.

6、将多功能清洗机枪头调成喷雾状；

6, the multi function cleaning machine gun head is transferred into spray shape.

7、将散热片上的感温探头用塑料胶布黏贴起来，使用多功能清洗机对空调的散热片和风轮依次的喷洗（风轮一边喷一边用手转动）；

7, the heat sink temperature probe with a plastic adhesive tape, the use of multi function cleaning machine for air conditioning fins and a wind wheel in turn jet washing (wind wheel side spray hand rotation);

8、使用格科专用空调清洗剂均匀的对空调散热片和风轮进行喷洒（风轮一边喷一边用手转动），等待反应污渍10-15分钟；

8, the use of special air conditioning Geke cleaning agent for spraying air conditioning fins and a wind wheel (wind wheel side spray hand rotation), wait 10-15 minutes reaction stains;

9、将过滤网、导风片均匀喷上空调清洗剂，在自来水下冲洗并用软毛刷刷洗干净，放置一旁等待安装；

9, filter, air guiding plate is evenly sprayed on the cleaning agent, in tap water to rinse and wash it with a soft brush, set aside for installation;

10、多功能清洗机调节成喷雾状，使用软圆毛刷由上到下对散热片进行刷洗、并用设备进行冲洗，污渍流入排水槽，排除室外；

10, the multi-function cleaning machine is adjusted to spray shape. The soft circular brush is used to scrub and remove the heat sink from top to bottom, and rinse with the equipment, and the stain enters the drainage tank to exclude the outdoor.

11、多功能清洗机调试成水柱状，用毛刷边刷边冲洗风轮，污水流至空调清洗防水罩，并通过导管流入水桶中，至没有污水流出为止；

11, the multi-function cleaning machine debugged into a water column and washed the wind wheel with brush. The sewage flows to the air conditioner to clean the waterproof cover, and flows into the bucket through the pipe until no sewage goes out.

12、撕下感温探头用塑料胶布，摘下清洗罩，将外壳擦拭干净.依次装好过滤网、导风片。

12, tear off the temperature sensor with plastic rubber cloth, remove the cleaning cover, wipe the shell clean. In turn loading filter net, guide film.

13、插上电源，检查各项功能是否正常；

13, plug in the power, check the function is normal;

14、收拾垃圾，环境整理,把携带工具设备等装配整齐。

14, clean up the garbage, the environment, and carry out the equipment and equipment.

 

 

 

 

柜机清洗流程：

Cabinet cleaning process:

1.确定空调外壳螺丝所在位置并拆下，拆卸空调上、下面板及拉出过滤网；

1. determine the position of the screw of the air conditioning shell and dismantle it, disassemble the upper and lower panel of the air conditioner and pull out the filter net.

2.多功能清洗机枪头调成为喷雾状；

2. multi function cleaning machine gun head is transferred into spray shape.

3.使用多功能清洗机对空调散热片进行清洗；

3. use the multifunctional cleaning machine to clean the heat sink of the air conditioner.

4.将空调清洗剂均匀喷洒在散热片后，等待10-15分钟充分反应污渍；

4. the air conditioner cleaning agent is evenly sprinkled in the heat sink, waiting for 10-15 minutes to fully respond to stains;

5.将空调外壳、过滤网均匀喷上空调清洗剂。在自来水下冲洗并用软毛刷刷洗干净，放置一旁等待安装；

5. the air conditioning shell and filter net are evenly sprayed on the air conditioner cleaning agent. In the tap water to rinse and wash it with a soft brush, set aside for installation;

6.将抹布打湿拧干并喷上空调清洗剂，对空调风轮以及底部依次擦洗干净；

6. wet the rag to dry and spray on the air conditioner cleaning agent, clean the air air wheel and the bottom in turn.

7.药剂充分分解散热片污渍后，使用软圆毛刷由上到下对散热片进行刷洗，并使用多功能清洗机对散热片进行再次冲洗，可观察污水流入空调排水槽，排往室外；

7., after fully decomposing the heat sink stains, the soft round brush is used to scrub the heat sink from top to bottom, and the multifunctional radiator is used to wash the heat sink again. It can be observed that the sewage flows into the air conditioning drain tank and is discharged to the outside.

8.依次装上过滤网、上面板、下面板；

8., the filter net, the upper panel and the lower panel are installed in turn.

9.把空调清洗喷在抹布上擦洗空调外壳，如遇塑料壳表面发黄或顽固污渍，可涂上亮洁膏后，用百洁布反复擦洗。

9. the air conditioning cleaning spray on the cloth to scrub the air conditioner shell, if the plastic shell surface yellow or stubborn stains, can be painted on the cream, with a hundred clean cloth repeatedly scrubbed.

10.插上电源，检查各项功能是否正常；

10. plug in the power, check the function is normal;

11.收拾垃圾，环境整理,把携带工具设备等装配整齐。

11. clean up the garbage, finish the environment, and assemble the equipment and equipment.

 

 

吸顶式空调（天花机）清洗流程

Suction top air conditioning (smallpox) cleaning process

1.关闭空调电源，依照顺序卸下空调底盖、过滤网、用扳手把风轮拆下放置一旁等待清洗；

1. turn off the air conditioning power, in order to remove the bottom cover and the air conditioning filter, use a wrench to remove wind wheel aside for cleaning;

2.多功能清洗机枪头状调试成雾状；

2. multi function cleaning machine gun head shape debug foggy.

3.使用多功能清洗机对空调的散热片进行一遍的清洗；

3. use the multifunctional cleaning machine to clean the heat sink of the air conditioner.

4.将空调清洗剂均匀喷洒在散热片上，等待10-15分钟使污渍充分溶解；

4. the air conditioner cleaning agent is evenly sprinkled on the radiator, waiting for 10-15 minutes to fully dissolve the stain;

5.将空调风轮、底盖、滤网喷上空调清洗剂，并使用清洗机冲洗干净；

5. the air conditioning air wheel, bottom cover and filter net are sprayed on the air conditioner cleaning agent, and the cleaning machine is washed with the cleaning machine.

6.散热片污渍充分溶解后，用软毛刷配合多功能清洗机将散热片清洗干净；

6. after the dissolving of the heat sink stains fully, the radiator is cleaned with the soft brush and the multifunctional cleaning machine.

7.依次装回过滤网、风轮、盖板；

7., the filter net, the wind wheel and the cover board are installed in turn.

8.将空调清洗喷在湿抹布上把空调外壳擦洗干净；

8. spray the air conditioning cleaning on the wet cloth to clean the shell of the air conditioner.

9.接通电源，检查各项功能是否正常；

9. connect the power supply and check whether the functions are normal.

10、收拾垃圾，环境整理,把携带工具设备等装配整齐。

10, clean up the garbage, the environment, and carry out the equipment and equipment.